using Instruction:

Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “■ SET”key and then through “▲ UP” and“▼

DOWN” adjust preset temperature, after adjust it and press“■ SET”key confirm it. when cold film, the preset temperature is 50 ℃ .,the max temperature is 50 ℃.According to the viscosity of the glue, and adjust preset temperature.

Turn: This machine don’t have continuous reverse function;

In the "continuous" state it only can " turning";

In the "point move" state, through the pedal switch can "turning" or "reverse".

Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move".

General Using and installation method

Note：The hex nuts must be tighten! If loose will appear heating power electric spark change,and broken wire and other components.

Air Pressure Adjustment:

There is a Filter Voltage Stabilizer at the right back of the machine, as the picture;Pull the knob of the filter voltage stabilizer up softly, air pressure increases when rotating at clockwise direction. Air pressure decreases when rotating at the counterclockwise direction. Normal air pressure is 0.2Mpa.

A-Pressure adjusting valve B-Pressure adjusting valve C-locking screw nut

1. When the parallelism gap of the rollers is slight, it can be adjusted by the following method:

a. Moving screw A to adjust the balance of the roller while it ’ s rising. Find out which side of the roller rises slower, then move the screw outward ( Or find out which side rises faster, then move the screw inward). Then raise and lower the roller until the roller is balanced.

b. Move screw B to adjust the balance of roller while it’ s falling. Find out which side of the roller falls slower, then move the screw outward ( Or find out which side falls faster, then move the screw inward). Then raise and lower the roller until the roller is balanced.

(Adjust the air pressure to 0.1MPa, the movement of the roller is slower than normal. It’s convenient to observe. )

Film laminating

Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation.

Preheating ready to work:

1. Fall down tne upper nip roller;

2. Press the "continuous" and "turning" switch, governor rotate to the "1";

3. Open the main switch;

4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 ℃ , when low temperature/cold laminating, the preset temperature set to 45 ℃ (to working temperature need about 10-20 minutes)

5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it.

6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them. 

The general questions and methods

Problem  

Control panel have no electricity

Method:
Check the power and emergency button

Problem Don’t turn

Method:

Lift a little the upper roller

Adjust friction
Tighten sprocket key

Contact with motor or governor

Problem

Laminated paper isn't clear and have white point

Method:

Increase roller temperature

Clean the dust

Contact suppliers to replace film

Problem

laminated paper have pleated bubbles

Method:

Adjust roller force

Put paper in 90 angle into rubber roller

Increase speed and reduce temperature

Problem

Film fold

Method:

Adjust material-roller’s resistance

Adjust to the required temperature

Package:

Machine Dimension	74" x 27" x 45" (1880mm x 680mm x 1140mm)
Machine Weight	280lb (140kg)
Package	Fumigation free package
Packing Size	81" x 28" x 28" (2060mm x 710mm x 720mm)
Gross Weight	441lb (200kg)